Carte mère Mini ITX JNF9T-2930
Référence : CMJEJNF9T-2930
Marque : Jetway
Mini ITX, Proc. Intel Celeron N2930, Quad Core, 1.86Ghz, LVDS, Glan,
VGA, HDMI, 8xUSB2, PCIex1, mPCIe, 2xSATA2, 5xRS232, LPT, PS/2, 12V DC-in
VGA, HDMI, 8xUSB2, PCIex1, mPCIe, 2xSATA2, 5xRS232, LPT, PS/2, 12V DC-in
Carte mère industrielle Mini ITX
- Intel Celeron N2930 Processor
- Embedded Long-life Series, Lifecycle through Q1'2019
- Supports DDR3L-1333 1.35V SODIMM up to 8GB Total
- Built-in +12V DC-In
- ECO-design for EuP/ErP
- Intel Celeron N2930 Processor
- Embedded Long-life Series, Lifecycle through Q1'2019
- Supports DDR3L-1333 1.35V SODIMM up to 8GB Total
- Built-in +12V DC-In
- ECO-design for EuP/ErP
.
| Jetway NF9T Mini-ITX Motherboard | |
| Processor | Intel® Celeron N2930 SoC, 1.83GHz – 2.16GHz Burst, Quad-Core, 7.5W TDP/4.5W SDP Intel® Atom E3827 SoC, 1.75GHz, Dual-Core, 8W TDP, with AES-NI support |
| Memory | 1 x 204-pin SODIMM DDR3L-1333 Single Channel up to 8 GB (1.35V required) |
| Graphics | Intel HD Graphics, 313MHz - 854MHz for N2930 Intel HD Graphics, 542MHz - 792MHz for E3827 |
| Audio | Realtek ALC662 2.1 Channel HD Audio with 3W Speaker Amplifier |
| LAN | 1 x Intel 82583V Gigabit Ethernet |
| Storage | 2 x SATA2 3Gb/s Connectors 1 x Full-size mSATA slot |
| Super IO | FINTEK F81866A |
| Back Panel Connectors | |
| 1+12 DC-in jack 1 HDMI 1 VGA 1 Parallel 3 USB 2.0 1 PS2 Mouse/Keyboard Combo 1 RS232/422/485 jumperless COM Port 1 RS232 COM Port 1 RJ45 LAN (10/100/1000) 1 USB 3.0 1 3.5mm Audio Jacks (Line Out & MIC In) | |
| Onboard I/O Connectors | |
| 1PCI Express x1 Slot 1 Full size mSATA Slot (shares with one SATA) 1 Half size mini PCI-E Slot 2 SATA2 3Gb/s Connectors 3 USB 2.0 Pin Headers for up to 5 additional USB 2.0 Ports 3 Serial Port Headers (RS232, +5V/+12V) 1 24-bits Dual Channel LVDS/Inverter 1 GPIO header 1 Chassis Intrusion header 1 AT/ATX Mode jumper 1 9-pin Audio header 1 2-pin LAN LED header 1 2-pin SPDIF header 1 4-pin SMBUS header 1 Front Panel header 3 Fan headers 1 4-pin Power Output (Male) 1 2-pin +12V Alternate Power Connector (Molex 5566-2) | |
| Power Supply for NF9T | |
| External Power Supply– the board can be powered with a 12V external power supply though a DC connector on the back panel. The rear 12V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is 12V and the shell is GND. Internal Power Supply – the board can alternatively be powered via the internal 12V DC 1 x 2 power connector, where pin 1 is GND and pin 2 is +12 (±10%) VDC. The internal 1 x 2 power connector is a Molex 5566-2 header which accepts a Molex 5557-02R connector from the power supply. Based on power consumption test results, the recommended power rating is 60 W (12V/5A). Caution: There is no isolation circuitry between the external 12V DC jack and the internal 2 x 2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external 12V DC jack is covered if the internal 2 x 2 power connector is to be used. | |
| Market Segments Supported | |
| √ Digital Signage √ Panel PC √ Industrial Automation/Control √ All-In-One √ Retail (POS/Kiosk/ATM) √ Casino Gaming √ Thin Client | |
| Environment | |
| Operating Temperature : 0 ~ 60°C Storage Temperature : -20 ~ 85°C | |
Mini ITX, Proc. Intel Celeron N2930, Quad Core, 1.86Ghz, LVDS, Glan,
VGA, HDMI, 8xUSB2, PCIex1, mPCIe, 2xSATA2, 5xRS232, LPT, PS/2, 12V DC-in
VGA, HDMI, 8xUSB2, PCIex1, mPCIe, 2xSATA2, 5xRS232, LPT, PS/2, 12V DC-in