> >>>>Carte mère Mini ITX NC9T
Carte mère Mini ITX NC9T Agrandir l'image

Carte mère Mini ITX NC9T

CMJEJNC9T-1037

Jetway

Mini ITX, INTEL NM70 Chip. INTEL CELERON 1037 CPU, INTEL GT1 GPU,
2xGLAN, VGA,HDMI, 24Bit LVDS, 6xUSB2.0, PCIExpress, 2xMini-PCIe,
Ext RS232, 5 Int.Xrs232, RS485, 1X SATAII, 1xSATAIII, Shared M-SATA

Plus de détails

Carte mère industrielle Mini ITX avec processeur mobile Celeron 1037U Dual core

- 3rd Generation Intel Mobile Celeron ULV Processor
- HDMI, VGA and 24-bit Dual Channel LVDS
- RJ11 Jack with +12V/+24V Power for Cash Drawers
- 6 x COM Ports with +5V/+12V
- Built-in +12V DC or Internal 2-pin +12V Power Connector
- ECO-design for EuP/ErP
Jetway NC9T Mini-ITX Motherboard
ProcessorIntel® Celeron 1037U Dual Core Mobile Processor 1.8 GHz @ 17W (FCBGA1023)
ChipsetIntel NM70 (AKA Panther Point)
Memory1 x 204-pin SODIMM DDR3-1066/1333 Single Channel (up to 8 GB)
GraphicsIntel HD2000 Graphics
AudioRealtek ALC662 2.1 Channel HD Audio
LAN2 x Realtek RTL8111G Gigabit Ethernet with Enhanced Surge Protection
Storage1 x SATA3 6Gb/s Connector
1 x SATA2 3Gb/s Connectors
1 x mSATA (Share with Mini PCI-E slot)
Super IOFINTEK F81866A
Back Panel Connectors
1 +12V DC-In jack
4 USB 2.0
1 PS/2 Keyboard/Mouse
1 RJ-11 port (+12V/+24V)
1 HDMI
1 VGA
1 Parallel port
1 COM port (RS232/422/485, +5V/+12V)
2 RJ45 LAN (10/100/1000)
2 3.5mm Audio Jacks (Line Out, Mic In)
Onboard I/O Connectors
1 PCI Express x1 slot
1 Full size mini PCI-E Slot (share with mSATA)
1 Half size mini PCI-E Slot
1 SATA3 6Gb/s Connectors
1 SATA2 3Gb/s Connectors
1 USB Pin Headers for up to 2 additional USB 2.0 Ports
5 Serial Port Headers (RS232, +5V/+12V)
1 24-bits Dual Channel LVDS connector/Inverter
1 Chassis Intrusion Header
1 9-pin Audio header
1 Front Panel header
3 Fan headers
1 2-pin +12V Alternate Power connector
Power Supply for NC9T
External Power Supply – the board can be powered with a 12V external power supply though a DC connector on the back panel. The rear 12 VDC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is 12V and the shell is GND.

Internal Power Supply – the board can alternatively be powered via the internal 12V DC 1 x 2 power connector, where pin 1 is GND and pin 2 is +12 (±10%) VDC.

Based on power consumption test results, the recommended minimal power rating is 60W (12V / 5A).

Caution: There is no isolation circuitry between the external 12 VDC jack and the internal 1 x 2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external 12 VDC jack is covered if the internal 1 x 2 power connector is to be used.
Market Segments Supported
√ Digital Security & Surveillance
√ Digital Signage
√ Gaming
√ Industrial Automation/Control
√ Medical
√ Retail (POS/Kiosk/ATM)
√ Networking/Storage Server/Mail Server/Print Server
√ Thin Client
√ HTPC